WHEEL BEARING KIT BMW 3 Cabriolet (E36) 318 i 115BHP Top German Quality

d:45 mm; d1 ≈:52 mm; C:25 mm; b1:4.6 mm; Specific dynamic load factor K:150 N/mm²; Specific static load factor K0:500 N/mm²; Mass plain bearing:0.49 kg; Material constant KM:330; Da max.:63.6 mm; B:40 mm;

J1:85.725 mm; H2:60.325 mm; Initial grease fill:481.95 g; P150°:85.9 kN; End plug (suffix Y):EPR 18; Eye bolt:3/8-16 UNC; P90°:149 kN; N1:28.575 mm; J min.:396.875 mm; Cap bolt recommended tightening torque:400 N·m;

H1:114.3 mm; P180°:42.7 kN; Cap bolt:2 x 3/4-10 UNC; Bearing:22317 EK; End plug (suffix Y):EPR 10; H:222.25 mm; Mass pillow block:34 kg; N1:22.225 mm; RG:3/8 NPT; P120°:39.1 kN;

Db1:55.4 mm; RG:1/4-28 UNF; Basic static load rating C0:6.55 kN; Bearing:YAR 204-012-2RFGR/HV; A5:25.3 mm; B:31 mm; Thread grub screw G2:1/4-28 UNF; s1:18.3 mm; T:32.6 mm; Db2:59.7 mm;

Grease Speed Rating n1:11000 rpm; Oil Speed Rating n2:14000 rpm; B:17.00 mm; Fillet Radius ra:1.00 mm; Sealed Speed Rating n3:7500 rpm; d:25.000 mm; Basic Dynamic Radial Load Rating C:21200 N; Accessories:One Seal; Basic Static Radial Load Rating Co:10800 N; Grease Speed Rating Open/Shielded n1:11000 rpm;

d:45 mm; d1 ≈:52 mm; C:25 mm; b1:4.6 mm; Specific dynamic load factor K:150 N/mm²; Specific static load factor K0:500 N/mm²; Mass plain bearing:0.49 kg; Material constant KM:330; Da max.:63.6 mm; B:40 mm;

J1:85.725 mm; H2:60.325 mm; Initial grease fill:481.95 g; P150°:85.9 kN; End plug (suffix Y):EPR 18; Eye bolt:3/8-16 UNC; P90°:149 kN; N1:28.575 mm; J min.:396.875 mm; Cap bolt recommended tightening torque:400 N·m;

H1:114.3 mm; P180°:42.7 kN; Cap bolt:2 x 3/4-10 UNC; Bearing:22317 EK; End plug (suffix Y):EPR 10; H:222.25 mm; Mass pillow block:34 kg; N1:22.225 mm; RG:3/8 NPT; P120°:39.1 kN;

Db1:55.4 mm; RG:1/4-28 UNF; Basic static load rating C0:6.55 kN; Bearing:YAR 204-012-2RFGR/HV; A5:25.3 mm; B:31 mm; Thread grub screw G2:1/4-28 UNF; s1:18.3 mm; T:32.6 mm; Db2:59.7 mm;

Axial load factor Y:0.4; ra max.:1.5 mm; D:100 mm; Limiting value e:0.3; rb max.:1 mm; Da max.:91.4 mm; db min.:68 mm; da max.:64 mm; da min.:62 mm; r1,2 min.:1.5 mm;

Axial load factor Y:0.4; ra max.:1.5 mm; D:100 mm; Limiting value e:0.3; rb max.:1 mm; Da max.:91.4 mm; db min.:68 mm; da max.:64 mm; da min.:62 mm; r1,2 min.:1.5 mm;